Anniversary Special Edition Eachine Minicube Flytower 20x20mm Compatible Frsky Flysky DSM RX F3 ESC - Compatible DSM2/DSMX Receiver

€ 54,99

Anniversary Special Edition Eachine Minicube Flytower 20x20mm Compatible Frsky Flysky DSM RX F3 V1.1 6DOF Blheli_S 10A ESC Dshot600 Description: Brand name: Eachine Mount hole: 20mm*20mm Size: 27mm*27mm*20mm Weight: 9.4g 1. Eachine Minicube Receiver 1). Eachine Minicube DSM2/ DSMX satellite Receiver Frequency range: 2.403-2.479Ghz Input power: 5V Response time: 22ms / 11MS Resolution: 2048 Display method: LED Operating voltage: 3.3V Working current: 60MA Size: 27mm*27mm*7mm Mount hole:20mm*20mm Weight: 3.1 g Antenna length: 100mm Data format: Serial port Protoco: DSM2/DSMX Distance: no ground interference (1 m from the ground ) > 300m Uses: indoor small aircraft. Compatible Transmitters: DSM2 / DSMX series of remote control Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator 2). Eachine Minicube Flysky 8CH AFHDS2A receiver Channels: 8CH Model type: Multi-rotor Frequency range: 2.408-2.475GHz 2.4GHz system: AFHDS 2A Transfer method: FHSS Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator Antenna length: 100mm No ground interference ( Transmitting and receiving 1 m from the ground): >300m Working current: 40mA Size: 27*27*7mm Mount hole:20mm*20mm Weight: 3.1g Ibus output with failsafe Compatible Transmitter: Compatible with FS-i4, FS-i6, FS-i6S, FS-i6X, FS-i10, FS-GT2E, FS-GT2G, FS-GT2F 3). Eachine Minicube Frsky Compatible 2.4G 8CH Receiver: Frequency range: 2.403-2.479Ghz Channels: 8CH Work mode :D8 Mode Output: SBUS Antenna length: 100mm No ground interference ( Transmitting and receiving 1 m from the ground): >500m Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator Working current: 80mA Dimensions: 27*27*7mm Weight: 3.5g Compatible with FRSKY ACCST Compatible with X9D(Plus)DJT/DFT/DHT Telemetry: RSSI, 1S-3S voltage (A1), 1S-3S voltage (A2) 2. Eachine Minicube F3 V1.1 6DOF Flight Controller: Size: 27mm*27mm*5mm Mount hole: 20mm*20mm Working voltage: 2-3S Lipo Processor: STM32 F303 MCU Sensor: SPI Sensor MPU6000 Built-in Betaflight OSD (Batt voltage, RSSI, Fly mode, Flytime, Craft name etz.) Firmware version: Betaflight 3.1 Dshot ready Target: OmnibusF3 This V1.1 version comes with SH1.0 plug instead of USB interface, intergrated filtration module. 3. Eachine Minicube 10A BLHeli_S 4 In 1 ESC: Size: 27mm*27mm*5mm Mount hole: 20mm*20mm Firmware version: BLHELI_S 16.5 BB2, 48MHZ Chip Lipo Battery: 2-3S Con. Current: 10A Peak Current: 15A (10S) BEC: 5V @0.1A Programming: YES Betaflight passtrough ready Dshot600 ready(Default) Support oneshot42 oneshot125 Multishot Dshot Damped light on Features: STM32 F303MCU + BLHELI_S ESC make your Operating feel more stabilly and silky Jaw-dropping flight performance LED_STRIP solder pin BUZZER Ready Betaflight support Acro mode / Air mode /Angle mode support Built-in OSD(Using F3 MCU controls OSD over SPI bus in DMA mode) OSD Configuration has been include in BETAFLIGHT GUI Radio Stick to control PID Tunes Package included: 1 x Minicube Receiver 1 x Minicube F3 V1.1 6DOF Flight Controller 1 x Minicube 10A BLHeli_S 4 In 1 ESC (This version of flytower comes already soldered)